Welcome to your new project. Imagine what you can build here.

BOURNS 3314G-1-104E ±20% ±100ppm/℃ 250mW 100kΩ SMD Variable Resistors/Potentiometers ROHS

Adafruit 1304 - Microlipo Charger V2

Welcome to your new project. Imagine what you can build here.

Haptic Glove Controller Board NUCLEO-F411RE based

Model for the PCA9685 Breakout Board Ideally, standoffs could be added or a 2.54mm right angle female header

IMU board used for finger-tracking in haptic gloves Difference from TinyIMU 4.0 is that the interrupt and ADC pins are not broken out to save space

THD051010CLGF https://datasheet.lcsc.com/lcsc/1811021340_THD-THD0510-10CL-GF_C283121.pdf Clamshell 10 Bottom Contact Surface Mount 0.5mm SMD,P=0.5mm FFC/FPC Connectors ROHS 2.15 THD THD0510-10CL-GF

IMU board used for finger-tracking in haptic gloves

ATTiny10 Based Snowflake PCB Programmed using Arduino over Tiny Programming Interface Roughly 88x80 mm size

Lipo Charger Shield. Directly plugs into Arduino Uno R3. Charge rate set with solder jumpers. Use with any MCU through tapping the VIN pin for power. VIN pin takes either

A Bluetooth Power Logger utilizing Seeed Studio's XIAO nRF52840 uC Power Monitoring handled using the INA260 IC, this design should be safe for usage under 36V 8A. Higher current rating will require larger trace widths on the main power trace. Attach your Power Supply to V+ and GND. Then attach your loading device to LOAD+ and GND.

Current & Power Monitors & Regulators 36V, 16-bit, precision i2c output current/voltage/power monitor w/ int. shunt resistor 16-TSSOP -40 to 125

The Wi-Fi Notecard is a version of the Blues Notecard with Wi-Fi connectivity in place of cellular. The device is the same size as all cellular Notecards and follows the same m.2 pinout. What's more, the Wi-Fi Notecard uses the same powerful JSON-based programming interface, meaning that developers can easily add Wi-Fi as a deployment option for their IoT solutions, with minimal impact to their existing host applications. WiFi Version

Round Standoff Threaded M2.5x0.45 Steel 0.098" (2.50mm)

M.2. Key E edge connector and screw-down port for Notecard Nano-SIM slot for (optional) additional carrier connectivity Qwiic I2C ports for attaching external peripherals JST connectors for LiPo battery and solar panel Micro-USB to power device and provide USB interface to Notecard This product requires a Notecard #blues

Expansion Shield for the Blues Feather Swan Carrier #blues

Feather-compatible dev board, powered by an STM32L4+ @ 120 MHz with 2MB of Flash and 640KB of RAM Expandable to 55 pins for access to additional I/O and buses Plenty of Flash and RAM for edge ML workloads or complex applications Support for C/C++, Arduino, and CircuitPython CORTEX Debug connector, enabling the use of Visual Studio Code, IAR, and STM32CubeIDE with optional SWD programmer #blues

IMU board used for finger-tracking in haptic gloves

Hand-sized pumpkin PCB The copper has been removed at the eyes and mouth so light can shine through from the back! 555 Timer has been selected to provide LED flashing at 0.5Hz Adjust R2 for differing speed!

This is a 7-segment controller. It runs on a 3-bit counter so the count is from 0-7. Buttons to toggle reset, pause, increment. Knobs to control speed and lighting configuration. Try the simulation here: https://www.flux.ai/jbreidfjord-dev/7-seg-3-bit-counter

This is a simulation of a 7-segment counter using digital logic gates (and, or, not). Three pulsed sources are required at A,B,C and should count out the binary 000-111. This is manufacturable and has a PCB design for it!

Change History from V1: -Font Bigger for SMD Footprint and IC designators -Confirmed that V1 worked for LED energy harvesting and NFC write/read Forked an amazing PCB business card from Mark Wu and added a SMD footprint and silkscreen art.

Development Boards & Kits - ARM STM32 Nucleo-64 development board STM32F411RE MCU, supports Arduino & ST morpho

Pre-soldered stackable 40-pin header for plugging into a RPi M.2. Key E edge connector and screw-down port for Notecard Nano-SIM slot for (optional) additional carrier connectivity Grove I2C port for attaching external peripherals Includes U.FL cellular/Wi-Fi antenna (GPS requires U.FL active antenna) Micro-USB to power device and provide USB interface to Notecard This product requires a Notecard

AFC01S10FCA00 FPC Connector

Change History from V1: -Font Bigger for SMD Footprint and IC designators -Confirmed that V1 worked for LED energy harvesting and NFC write/read Forked an amazing PCB business card from Mark Wu and added a SMD footprint and silkscreen art.

150 µF 25 V Aluminum - Polymer Capacitors Radial, Can - SMD 30mOhm 4000 Hrs @ 125°C

Linear Voltage Regulator IC Positive Fixed 1 Output 2A 6-DFN (3x3)