Welcome to your new project. Imagine what you can build here.

Breadboard adapter for the Moddo pinch: a 2×8 1.27 mm through-hole center header broken out to 2.54 mm through-hole headers on an 18 × 15 mm, 2-layer PCB.

Small breadboard-friendly breakout/carrier PCB for the Moddo pinch SAMD11 dev board, converting its 16-pin 1.27 mm header to 2.54 mm through-hole breakout pins. Mechanical dimensions are marked verify-against-hardware until Moddo publishes official drawings.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Built-in power-on reset circuit、Integrated intelligent reverse connection protection function SMD2020-4P RGB LEDs(Built-in IC) ROHS SMD2020-4P

A compact battery-powered door/window sensor built around the ESP32-C3-MINI-1-N4 module. The design uses a single non-rechargeable AA cell with a TPS613221A 3.3 V boost regulator, reed switch magnetic contact sensing, low-power wake/report/sleep firmware strategy, RGB status LED for setup feedback, BOOT/EN controls, programming header, and input polarity protection. It is intended for smart-home security and automation applications, supporting WiFi or Bluetooth LE hub reporting with emphasis on low idle current, reliable RF burst power delivery, and field-replaceable battery operation. #ESP32-C3 #BLE #WiFi #DoorSensor #WindowSensor #ReedSwitch #LowPower #BatteryPowered #SmartHome #IoT

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

A self-contained “retro PC” platform built around the ESP32, exposing classic PC-style IO: VGA video, PS/2 keyboard/mouse, audio-out to an onboard speaker, microSD storage, plus USB-C for power and USB-UART for programming/debug.

AI Brick Phone AMP

Big Flux logo size 47x18 mm

Pushbutton Switch SPST-NO Keyswitch Through Hole This switch is used in keyboards like: Planck Vortexgear KBD67 ErgoDox leopold WorkLouder Varmilo Ducky Durgod Mistel Keebio Iris iKBC WASD Keychron Filco and many others #Geteron #GateronKS

Light Dependent Resistors (Photocell) #commonpartslibrary #sensor #Opticalsensor

This project designs a Linux Single Board Computer using STM32MP157FAC1, featuring DDR memory, a power management IC, USB and SD card interfaces, and essential user controls, aimed at versatile embedded applications.

50-W Stereo Analog Input Class-D Audio Amplifier with a small number of external components mounted on a circuit board that can be used to directly drive a speaker with an external analog audio source as the input; can also be configured as a 100-W, Class-D mono audio amplifier in PBTL mode.

Connectors / Battery Connectors

Electronic Fuse Regulator 2.5A 6-WSON (2x2) The TPS25200 is a 5-V eFuse with precision current limit and overvoltage clamp. The device provides robust protection for load and source during overvoltage and overcurrent events.

2.45GHz Center Frequency Band Pass RF Filter (Radio Frequency) 100MHz Bandwidth 1.5dB 0805 (2012 Metric), 4 PC Pad

USB-C (USB TYPE-C) USB 2.0 Receptacle Connector 24 (16+8 Dummy) Position Surface Mount, Right Angle

ARM® Cortex®-M3 series Microcontroller IC 32-Bit 72MHz 64KB (64K x 8) FLASH 36-VFQFPN (6x6) #microcontrollers #stm32 #commonpartslibrary

Bluetooth, WiFi 802.11b/g/n, Bluetooth v5.0 Transceiver Module 2.412GHz ~ 2.484GHz PCB Trace Surface Mount #BLE #WIFI #ESP32 #MCU #RF

3 Position Wire to Board Terminal Block Horizontal with Board 0.200" (5.08mm) Through Hole

2 Position Wire to Board Terminal Block Horizontal with Board 0.200" (5.08mm) Through Hole #simplifiedFootprint

Red 623nm LED Indication - Discrete 2V Radial, diameter 5mm 5.0mm, 2 pins through-hole THT LED 5mm #ledtht #LED #5mm

Interface - I/O Expanders Remote 4-Bit I C and SMBus I/O expander with configuration registers I/O Expander 4 I2C 1 MHz 10-VSSOP

40 power reduction compared to PCA9633 4 LED drivers. Each output programmable at: Off On Programmable LED brightness Programmable group dimming/blinking mixed with individual LED brightness 1 MHz Fast-mode Plus I2C-bus interface with 30 mA high drive capability on SDA output for driving high capacitive buses 256-step (8-bit) linear programmable brightness per LED output varying from fully off (default) to maximum brightness using a 1.5625 kHz PWM signal in Individual brightness m

Template for Raspberry Pi 5 Model Shield. Include an official pinout so you will always know Raspberry Pi names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Raspberry Pi itself along with the board outline on the silkscreen. #RaspberryPi #Raspberry #RaspberryPi5 #raspberry #Pi #RPi #Shield #template #project #project-template

Raspberry Pi 2, 3, 4, 5 or 400 Model B+ connector with RPi board outline and mounting holes. good for Raspberry Pi Shield projects. Insulation Height 0.335" (8.51mm) Compatible part number: PPPC202LFBN-RC #Raspberry_Pi #Shield #RPi #template #part